View MT9126_1092094.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

8-1 features full duplex transcoder with four encode channels and four decode channels 32 kb/s, 24 kb/s and 16 kb/s adpcm coding complying with itu-t (previously ccitt) g.726 (without 40 kb/s), and ansi t1.303-1989 low power operation, 25 mw typical asynchronous 4.096 mhz master clock operation ssi and st-bus interface options transparent pcm bypass transparent adpcm bypass linear pcm code no microprocessor control required simple interface to codec devices pin selectable ? law or a-law operation pin selectable itu-t or signed magnitude pcm coding single 5 volt power supply applications pair gain voice mail systems wireless telephony systems description the quad adpcm transcoder is a low power, cmos device capable of four encode and four decode functions per frame. four 64 kbit/s pcm octets are compressed into four 32, 24 or 16 kbit/s adpcm words, and four 32, 24 or 16 kbit/s adpcm words are expanded into four 64 kbit/s pcm octets. the 32, 24 and 16 kbit/s adpcm transcoding algorithms utilized conform to itu-t recommendation g.726 (excluding 40 kbit/s), and ansi t1.303 - 1989. switching, on-the-fly, between 32 kbit/s and 24 kbit/s adpcm, is possible by controlling the appropriate mode select (ms1 - ms6) control pins. all optional functions of the device are pin selectable allowing a simple interface to industry standard codecs, digital phone devices and layer 1 transceivers. linear coded pcm is provided to facilitate external dsp functions . ordering information MT9126ae 28 pin plastic dip MT9126as 28 pin soic -40 c to +85 c issue 3 july 1998 adpcm i/o pcm i/o control decode vdd vss pwrdn ic ms1 ms2 a/ format ms5 ms4 ms3 ms6 linear sel timing adpcmi adpcmo enb1 enb2/ f0od bclk f0i mclk/ c4i c2o en1 en2 pcmo1 pcmi1 pcmo2 pcmi2 full duplex quad transcoder figure 1 - functional block diagram MT9126 quad adpcm transcoder cmos
MT9126 8-2 figure 2 - pin connections pin description pin # name description 1 en1 enable strobe 1 (output). this 8 bit wide, active high strobe is active during the b1 pcm channel in st-bus mode. becomes a single bit, high true pulse when linear=1. in ssi mode this output is high impedance. 2 mclk/ c4i master clock/ c4i (input). this is a 4.096 mhz (minimum) input clock utilized by the transcoder function; it must be supplied in both st-bus and ssi modes of operation. in st-bus mode the c4i st-bus clock is applied to this pin. this synchronous clock is also used to control the data i/o flow on the pcm and adpcm input/output pins according to st-bus requirements. in ssi mode this master clock input is derived from an external source and may be asynchronous with respect to the 8 khz frame. mclk/ c4i rates greater than 4.096 mhz are acceptable in this mode since the data i/o rate is governed by bclk. 3 f0i frame pulse (input). frame synchronization pulse input for st-bus operation. ssi operation is enabled by connecting this pin to v ss . 4 c2o 2.048 mhz clock (output). this st-bus mode bit clock output is the mclk/ c4i input divided by two, inverted, and synchronized to f0i. this output is high-impedance during ssi operation. 5 bclk bit clock (input). 128 khz to 4096 khz bit clock input for both pcm and adpcm ports; used in ssi mode only. the falling edge of this clock latches data into adpcmi, pcmi1 and pcmi2. the rising edge clocks data out on adpcmo, pcmo1 and pcmo2. this input must be tied to v ss for st-bus operation. 6 pcmo1 serial pcm stream 1 (output). 128 kbit/s to 4096 kbit/s serial companded/linear pcm output stream. data are clocked out by rising edge of bclk in ssi mode. clocked out by mclk/ c4i divided by two in st-bus mode. see figure 13. 7 pcmi1 serial pcm stream 1 (input). 128 kbit/s to 4096 kbit/s serial companded/linear pcm input stream. data are clocked in on falling edge of bclk in ssi mode. clocked in at the 3/4 bit position of mclk/ c4i in st-bus mode. see figure 13. 8v ss digital ground. nominally 0 volts. 9 linear linear pcm select (input) . when tied to v dd the pcm i/o ports (pcm1,pcm2) are 16- bit linear pcm. linear pcm operates only at a bit rate of 2048 kbit/s. companded pcm is selected when this pin is tied to v ss . see figures 5 & 8. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 28 27 26 25 24 23 22 21 ms1 vdd ms3 ic ms4 format ms2 pwrdn adpcmi adpcmo ms5 ms6 en2 pcmo1 bclk pcmi1 linear enb2/ f0od vss c2o mclk/ c4i f0i pcmi2 enb1 pcmo2 en1 sel a/
MT9126 8-3 10 enb2/ f0od pcm b-channel enable strobe 2 (input) / delayed frame pulse (output). ssi operation: enb2 (input). an 8-bit wide enable strobe input defining b2 channel (ad)pcm data. a valid 8-bit strobe must be present at this input for ssi operation. see figures 4 & 6. st-bus operation: f0od (output). this pin is a delayed frame strobe output. when lin- ear=0, this becomes a delayed frame pulse output occurring 64 c4i clock cycles after f0i and when linear = 1 at 128 c4i clock cycles after f0i . see figures 7, 8, 9 & 13. 11 enb1 pcm b-channel enable strobe 1 (input). ssi operation: an 8-bit wide enable strobe input defining b1 channel (ad)pcm data. a valid 8-bit strobe must be present at this input for ssi operation. st-bus operation: when tied to v ss transparent bypass of the st-bus d- and c- chan- nels is enabled. when tied to v dd the st-bus d-channel and c-channel output timeslots are forced to a high-impedance state. 12 pcmo2 serial pcm stream 2 (output). 128 kbit/s to 4096 kbit/s serial companded/linear pcm output stream. clocked out by rising edge of bclk in ssi mode. clocked out by mclk/ c4i divided by two in st-bus mode. see figure 13. 13 pcmi2 serial pcm stream 2 (input). 128 kbit/s to 4096 kbit/s serial companded/linear pcm input stream. data bits are clocked in on falling edge of bclk in ssi mode. clocked in at the 3/4 bit position of mclk/ c4i in st-bus mode. see figure 13. 14 sel select (input). pcm bypass mode: when sel=0 the pcm1 port is selected for pcm bypass operation and when sel=1 the pcm2 port is selected for pcm bypass operation. see figures 6 & 9. 16 kbit/s transcoding mode: ssi operation - in 16 kbit/s transcoding mode, the adpcm words are assigned to the i/o timeslot defined by enb2 when sel=1 and by enb1 when sel=0. see figure 4. st-bus operation- in 16 kbit/s transcoding mode, the adpcm words are assigned to the b2 timeslot when sel=1 and to the b1 timeslot when sel=0. see figure 9. 15 a/ a-law/ ? law select (input). this input pin selects ? law companding when set to logic 0, and a-law companding when set to logic 1. this control is for all channels .this input is ignored in linear mode during which it may be tied to v ss or v dd . 16 format format select (input). selects itu-t pcm coding when high and sign-magnitude pcm coding when low. this control is for all channels.this input is ignored in linear mode during which it may be tied to v ss or v dd . 17 pwrdn power-down (input). an active low reset forcing the device into a low power mode where all outputs are high-impedance and device operation is halted. 18 ic internal connection (input). tie to v ss for normal operation. 19 20 21 ms1 ms2 ms3 mode selects 1, 2 and 3 (inputs). mode selects for all four encoders. ms3 ms2 ms1 mode 0 0 0 32 kbit/s adpcm 0 0 1 24 kbit/s adpcm 0 1 0 16 kbit/s adpcm in en1/enb1 when sel=0 in en2/enb2 when sel=1 0 1 1 adpcm bypass for 32 kbit/s and 24 kbit/s 1 0 0 adpcm bypass for 16 kbit/s 1 0 1 pcm bypass (64 kbit/s) to pcm1 if sel=0, pcm2 if sel=1 1 1 0 algorithm reset (itu-t optional reset) 1 1 1 adpcmo disable 22 v dd positive power supply. nominally 5 volts +/-10% pin description (continued) pin # name description
MT9126 8-4 notes: all unused inputs should be connected to logic low or high unless otherwise stated. all outputs should be left open circuit whe n not used. all inputs have ttl compatible logic levels except for mclk/ c4i which has cmos compatible logic levels and pwrdn which has schmitt trigger compatible logic levels. all outputs are cmos with cmos logic levels (see dc electrical characteristics). 23 adpcmi serial adpcm stream ( input). 128 kbit/s to 4096 kbit/s serial adpcm word input stream. data bits are clocked in on falling edge of bclk in ssi mode and clocked in on the 3/4 bit edge of mclk/ c4i in st-bus mode. 24 adpcmo serial adpcm stream (output). 128 kbit/s to 4096 kbit/s serial adpcm word output stream. data bits are clocked out by rising edge of bclk in ssi mode and clocked out by mclk/ c4i divided by two in st-bus mode. 25 26 27 ms4 ms5 ms6 mode selects 4, 5 and 6 (inputs). mode selects for all four decoders. ms6 ms5 ms4 mode 0 0 0 32 kbit/s adpcm 0 0 1 24 kbit/s adpcm 0 1 0 16 kbit/s adpcm in en1/enb1 when sel=0 in en2/enb2 when sel=1 0 1 1 adpcm bypass for 32 kbit/s and 24 kbit/s 1 0 0 adpcm bypass for 16 kbit/s 1 0 1 pcm bypass (64 kbit/s) to pcm1 if sel=0, pcm2 if sel=1 1 1 0 algorithm reset (itu-t optional reset) 1 1 1 pcmo1/2 disable 28 en2 enable strobe 2 (output). this 8 bit wide, active high strobe is active during the b2 pcm channel in st-bus mode. forced to high impedance when linear=1. pin description (continued) pin # name description functional description the quad-channel adpcm transcoder is a low power, cmos device capable of four encode and four decode operations per frame. four 64 kbit/s channels (pcm octets) are compressed into four 32, 24 or 16 kbit/s adpcm channels (adpcm words), and four 32, 24 or 16 kbit/s adpcm channels (adpcm words) are expanded into four 64 kbit/s pcm channels (pcm octets). the adpcm transcoding algorithm utilized conforms to itu-t recommendation g.726 (excluding 40 kb/s), and ansi t1.303 - 1989. switching on-the-fly between 32 and 24 kbit/s transcoding is possible by toggling the appropriate mode select pins (supports t1 robbed-bit signalling). all functions supported by the device are pin selectable. the four encode functions comprise a common group controlled via mode select pins ms1, ms2 and ms3. similarily, the four decode functions form a second group commonly controlled via mode select pins ms4, ms5 and ms6. all other pin controls are common to the entire transcoder. the device requires 25 mwatts (mclk/ c4i= 4.096 mhz) typically for four channel transcode operation. a minimum master clock frequency of 4.096 mhz is required for the circuit to complete four encode channels and four decode channels per frame. for ssi operation a master clock frequency greater than 4.096 mhz and asynchronous, relative to the 8 khz frame, is allowed. the pcm and adpcm serial busses support both st-bus and synchronous serial interface (ssi) operation. this allows serial data clock rates from 128 khz to 4096 khz, as well as compatibility with mitels standard serial telecom bus (st-bus). for st-bus operation, on chip channel counters provide channel enable outputs as well as a 2048 khz bit clock output which may be used by down-stream devices utilizing the ssi bus interface. linear coded pcm is also supported. in this mode the encoders compress, four 14-bit, twos complement (s,s,s,12,...,1,0), uniform pcm channels into four 4, 3 or 2 bit adpcm channels. similarly, the decoder expands four 4, 3 or 2 bit adpcm channels into four 16-bit, twos complement (s,14,...,1,0), uniform pcm channels. the data rate for both st-bus and ssi operation in this mode is 2048 kbit/s.
MT9126 8-5 serial (ad)pcm data i/o serial data transfer to/from the quad adpcm transcoder is provided through one adpcm and two pcm ports (adpcmi, adpcmo, pcmi1, pcmo1, pcmi2, pcmo2). data is transferred through these ports according to either st-bus or ssi requirements. the device determines the mode of operation by monitoring the signal applied to the f0i pin. when a valid st-bus frame pulse (244nsec low going pulse) is applied to the f0i pin the transcoder will assume st-bus operation. if f0i is tied continuously to v ss the transcoder will assume ssi operation. pin functionality in each of these modes is described in the following sub-sections. st-bus mode during st-bus operation the c2o, en1, en2 and f0od outputs become active and all serial timing is derived from the mclk/ c 4i and f0i inputs while the bclk input is tied to v ss . (see figures 7, 8 & 9.) basic rate ??and ??channels in st-bus mode, when enb1 is brought low, transparent transport of the st-bus "basic rate d- and c-channels" is supported through the pcmi1 and pcmo1 pins. this allows a microprocessor controlled device, connected to the pcmi/o1 pins, to access the "d" and "c" channels of a transmission device connected to the adpcmi/o pins. when enb1 is brought high, the ? and ? channel outputs are tristated. basic rate ? and ? channels are not supported in linear mode. (see figure 7.) ssi mode during ssi operation the bclk, enb1 and enb2/ f0od inputs become active. the c2o, en1, and en2 outputs are forced to a high-impedance state except during linear operation during which the en1 output remains active. (see figures 4, 5 & 6.) the ssi port is a serial data interface, including data input and data output pins, a variable rate bit clock input and two input strobes providing enables for data transfers. there are three ssi i/o ports on the quad adpcm; the pcmi/o1 pcm port, the pcmi/o2 pcm port, and the adpcmi/o port. the two pcm ports may transport 8-bit companded pcm or 16-bit linear pcm. the alignment of the channels is determined by the two input strobe signals enb1 and enb2/ f0od. the bit clock (bclk) and input strobes (enb1 and enb2/ f0od) are common for all three of the serial i/o ports. bclk can be any frequency between 128 khz and 4096 khz synchronized to the input strobes. bclk may be discontinuous outside of the strobe boundaries except when linear=1. in linear mode, bclk must be 2048 khz and continuous for 64 cycles after the enb1 rising edge and for the duration of enb2/ f0od. mode select operation (ms1, ms2, ms3, ms4, ms5, ms6) mode select pins ms1, ms2 and ms3 program different bit rate adpcm coding, bypass, algorithmic reset and disable modes for all four encoder functions simultaneously. when 24 kbit/s adpcm mode is selected bit 4 is unused while in 16 kb/s adpcm mode all adpcm channels are packed contiguously into one 8-bit octet. mode select pins ms4, ms5 and ms6 operate in the same manner for the four decode functions. the mode selects must be set up according to the timing constraints illustrated in figures 16 and 17. 32 kbit/s adpcm mode in 32 kbit/s adpcm mode, the 8-bit pcm octets of the b1, b2, b3 and b4 channels ( pcmi1 and pcmi2) are compressed into four 4-bit adpcm words on adpcmo. conversely, the 4-bit adpcm words of the b1, b2, b3 and b4 channels from adpcmi are expanded into four 8-bit pcm octets on pcmo1 and pcmo2. the 8-bit pcm octets (a-law or -law) are transferred most significant bit first starting with b7 and ending with b0. adpcm words are transferred most significant bit first starting with i1 and ending with i4 (see figures 4 & 7). reference itu-t g.726 for i-bit definitions. note that the sel pin performs no function in this mode. 24 kbit/s adpcm mode in 24 kbit/s mode pcm octets are transcoded into 3- bit words rather than the 4-bit words utilized in 32 kbit/s adpcm. this is useful in situations where lower bandwidth transmission is required. dynamic operation of the mode select control pins will allow switching from 32 kbit/s mode to 24 kbit/s mode on a frame by frame basis. the 8 bit pcm octets (a-law or -law) are transferred most significant bit first starting with b7 and ending with b0. adpcm words are transferred most significant bit first starting with i1 and ending with i3 (i4 becomes don? care). (see figures 4 & 7.) note that the sel pin performs no function in this mode.
MT9126 8-6 16 kbit/s adpcm mode when sel is set to 0, the 8-bit pcm octets of the b1, b2, b3 and b4 channels ( pcmi1 and pcmi2) are compressed into four 2-bit adpcm words on adpcmo during the enb1 timeslot in ssi mode and during the b1 timeslot in st-bus mode. similarily, the four 2-bit adpcm words on adpcmi are expanded into four 8-bit pcm octets (on pcmo1 and pcmo2) during the enb1/b1 timeslot. (see figures 4 & 7.) when sel is set to 1, the same conversion takes place as described when se l=0e xcept that the enb2/b2 timeslots are utilized. a-law or -law 8-bit pcm are received and transmitted most significant bit first starting with b7 and ending with b0. adpcm data are most significant bit first starting with i1 and ending with i2. adpcm byp ass (32 and 24 kbit/s) in adpcm bypass mode the b1 and b2 channel adpcm words are bypassed (with a two-frame delay) to/from the adpcm port and placed into the most significant nibbles of the pcm1/2 port octets. note that the sel pin performs no function for these two modes (see figures 6 & 9). linear, format and a/ pins are ignored in bypass mode. in 32 kb/s adpcm bypass mode, bits 1 to 4 of the b1, b2, b3 and b4 channels from pcmi1 and pcmi2 are transparently passed, with a two frame delay, to the same channels on adpcmo. in the same manner, the b1, b2, b3 and b4 channels from adpcmi are transparently passed, with a two frame delay, to the same channels on pcmo1 and pcmo2 pins. bits 5 to 8 are don? care. this feature allows two voice terminals, which utilize adpcm transcoding, to communicate through a system without incurring unnecessary transcode conversions. this arrangement allows byte-wide or nibble-wide transport through a switching matrix. 24 kb/s adpcm bypass mode is the same as 32 kb/s mode bypass excepting that only bits 1 to 3 are bypassed and bits 4 to 8 are don? care. adpcm byp ass (16 kbit/s) when sel is set to 0, only bits 1 and 2 of the b1, b2, b3 and b4 pcm octets (on pcmi1 and pcmi2) are bypassed, with a two frame delay, to the same channels on adpcmo during the enb1 timeslot in ssi mode and during the b1 timeslot in st-bus mode. similarily, the four 2-bit adpcm words on adpcmi are transparently bypassed, with a two frame delay, to pcmo1 and pcmo2 during the enb1 or b1 timeslot. bits 3-8 are don? care. (see figures 6 & 9.) when sel is set to 1, the same bypass occurs as described when sel = 0 except that the enb2 or b2 timeslots are utilized. linear, format and a/ pins are ignored in bypass mode. pcm byp ass when sel is set to 0, the b1 and b2 pcm channels on pcmi1 are transparently passed, with a two- frame delay, to the same channels on the adpcmo. simiarily, the two 8-bit words which are on adpcmi are transparently passed, with a two-frame delay, to channels b1 and b2 of pcmo1 while pcmo2 is set to a high-impedance state. (see figures 6 & 9.) when sel is set to 1, the b3 and b4 channels on pcmi2 are transparently passed, with a two frame delay, to the same channels on adpcmo. similarily, the two 8-bit words which are on adpcmi are transparently passed, with a two-frame delay, to channels b3 and b4 of pcmo2. in this case pcmo1 is always high-impedance if enb1 = 0. if enb1 = 1 during st-bus operation then the d and c channels are active on pcmo1. linear, format and a/ pins are ignored in bypass mode. algor ithm reset mode while an algorithmic reset is asserted the device will incrementally converge its internal variables to the 'optional reset values' stated in g.726. algorithmic reset requires that the master clock (mclk/ c4i) and frame pulse (enb1/2 or f0i) remain active and that the reset condition be valid for at least four frames. note that this is not a power down mode; see pwrdn for this function. adpcmo & pcmo1/2 disab le when the encoders are programmed for adpcmo disable (ms1 to ms3 set to 1) the adpcmo output is set to a high impedance state and the internal encode function remains active. therefore convergence is maintained. the decode processing function and data i/o remain active.
MT9126 8-7 when the decoders are programmed for pcmo1/2 disable (ms4 to ms6 set to 1) the pcmo1/2 outputs are high impedance during the b channel timeslots and also, during st-bus operation, the d and c channel timeslots according to the state of enb1. therefore convergence is maintained. the encode processing function and data i/o remain active. whenever any combination of the encoders or decoders are set to the disable mode the following outputs remain active. a) st-bus mode: enb2/ f0od, en1, en2 and c2o. also the ? and ? channels from pcmo1 and adpcmo remain active if enb1 is set to 0. if enb1 is brought high then pcmo1 and adpcmo are fully tri-stated. b) ssi mode: when used in the 16-bit linear mode, only the en1 output remains active. for complete chip power down see pwrdn. other pin controls 16 bit linear pcm setting the linear pin to logic one causes the device to change to 16-bit linear (uniform) pcm transmission on the pcmi/o1 and pcmi/o2 ports. the data rate for both st-bus and ssi operation in this mode is 2048 kbit/s and all decode and encode functions are affected by this pin. in ssi mode, the input channel strobes enb1 and enb2/ f0od remain active for 8 cycles of bclk for an adpcm transfer. the en1 output is high for one bclk period at the end of the frame (i.e., during the 256 th bclk period). in st-bus mode, the output strobes en1 and enb2/ f0od are adjusted to accommodate the required pcm i/o streams. the en1 output becomes a single bit high true pulse during the last clock period of the frame (i.e., the 256 th bit period) while enb2/ f0od becomes a delayed, low true frame-pulse ( f0od) output occuring during the 64 th bit period after the en1 rising edge. linear pcm on pcmi1 and pcmi2, are received as 14-bit, twos complement data with three bits of sign extension in the most significant positions (i.e., s,s,s,12,...1,0) for a total of 16 bits. the linear pcm data transmitted from pcmo1 and pcmo2 are 16-bit, twos complement data with one sign bit in the most significant position (i.e., s,14,13,...1,0) 32 and 24 kbit/s adpcm mode in 32 kbit/s and 24 kbit/s linear mode, the 16-bit uniform pcm dual-octets of the b1, b2, b3 and b4 channels (from pcmi1 and pcmi2) are compressed into four 4-bit words on adpcmo. the four 4-bit adpcm words of the b1, b2, b3 and b4 channels from adpcmi are expanded into four 16-bit uniform pcm dual-octets on pcmo1 and pcmo2. 16-bit uniform pcm are received and transmitted most significant bit first starting with b15 and ending with b0. adpcm data are transferred most significant bit first starting with i1 and ending with i4 for 32 kbit/s and ending with i3 for 24 kbit/s operation (i.e., i4 is don? care). (see figures 5 & 8.) note that the sel pin performs no function in this mode. 16 kbit/sadpcm mode when sel is set to 0, the four, 2-bit adpcm words are transmitted/received on adpcmo/i during the enb1 time-slot in ssi mode and during the b1 timeslot in st-bus mode. when sel is set to 1, the four, 2-bit adpcm words are transmitted/received on adpcmo/i during the enb2 timeslot in ssi mode and during the b2 timeslot in st-bus mode. (see figures 5 & 8.) pcm law control (a/ , format) the pcm companding/coding law invoked by the transcoder is controlled via the a/ and format pins. itu-t g.711 companding curves, -law and a-law, are selected by the a/ pin (0= -law; 1=a-law). per sample, digital code assignment can conform to itu-t g.711 (when format=1) or to sign-magnitude coding (when format=0). table 1 illustrates these choices. table 1 - companded pcm power down setting the pwrdn pin low will asynchronously cause all internal operation to halt and the device to go to a power down condition where no internal clocks are running. output pins c2o, en1, en2, pcmo1, pcmo2 and adpcmo and i/o pin f0od/ enb2 are forced to a high-impedance state. format 01 pcm code sign- magnitude a/ = 0 or 1 itu-t (g.711) (a/ = 0) (a/ = 1) + full scale 1111 1111 1000 0000 1010 1010 + zero 1000 0000 1111 1111 1101 0101 - zero 0000 0000 0111 1111 0101 0101 - full scale 0111 1111 0000 0000 0010 1010
MT9126 8-8 following the reset (i.e., pwrdn pin brought high) and assuming that clocks are applied to the mclk/ c4i and bclk pins, the internal clocks will still not begin to operate until the first frame alignment is detected on the enb1 pin for ssi mode or on the f0i pin for st-bus mode. the c2o clock and en1, en2 pins will not start operation until a valid frame pulse is applied to the f0i pin. if the f0i pin remains low for longer than 2 cycles of mclk/ c4i then the c2o pin will top toggling and will stay low. if the f0i pin is held high then the c2o pin will continue to operate. in st- bus mode the en1 and en2 pins will stop toggling if the frame pulse ( f0i) is not applied every frame. master clock (mclk/ c4i) a minimum 4096 khz master clock is required for execution of the transcoding algorithm. the algorithm requires 512 cycles of mclk/ c4i during one frame for proper operation. for ssi operation this input, at the mclk/ c4i pin, may be asynchronous with the 8 khz frame provided that the lowest frequency and deviation due to clock jitter still meets the strobe period requirement of a minimum of 512 t c4p - 25%t c4p (see figure 3). for example, a system producing large jitter values can be accommodated by running an over-speed mclk/ c4i that will ensure a minimum 512 mclk/ c4i cycles per frame is obtained. the minimum mclk/ c4i period is 61 ns, which translates to a maximum frequency of 16.384 mhz. extra mclk/ c4i cycles (>512/frame) are acceptable since the transcoder is aligned by the appropriate strobe signals each frame. figure 3 - mclk/ c4i minimum requirement bit clock (bclk) for ssi operation the bit rate, for both adpcm and pcm ports, is determined by the clock input at bclk. bclk must be eight periods in duration and synchronous with the 8 khz frame inputs at enb1 and enb2. data is sampled at pcmi1/2 and at adpcmi concurrent with the falling edge of bclk. data is available at pcmo1/2 and adpcmo concurrent with the rising edge of bclk. bclk may be any rate between 128 khz and 4096 khz. for st- bus operation bclk is ignored (tie to v ss ) and the bit rate is internally set to 2048 kbit/s. enb1 mclk/ c4i 512 t c4p - 25%t c4p minimum figure 4 - ssi 8-bit companded pcm relative timing adpcm i/o bclk enb1 enb2/ f0od pcmi/o1 adpcm i/o sel = 0 sel = 1 32 kb/s 24 kb/s 16 kb/s sel for 16 kb/s only b1 b2 pcmi/o2 1234 b1 b2 123x b1 b2 12 b3 b4 12 12 12121212 12 765 3 4 210 b3 b4 1234 123x 1234 b3 b4 123x 1234 123x b1 b2 b3 b4 765 3 4210 765 3 4 210765 3 4210 x = undetermined logic level output; don? care input two frame delay from data input to data output outputs high impedance outside of channel strobe boundaries
MT9126 8-9 figure 5 - ssi 16-bit linear pcm relative timing enb1 enb2/ f0od en1 adpcm i/o adpcmi/o b 1 1234 1234 1234 1234 123x 123x 123x 123x 12 sel = 1 sel = 1 sel = 0 bclk ... sel for 16 kb/s only (2.048 mhz only) pcmi/o1 pcmi/o2 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 b1 b2 s = 3 bits sign extension ? law is 13 bit 2? complement data (bits 0 -12) a-law is 12 bit 2? complement data (shifted left once and utilizing bits 1 - 12, bit 0 not defined) 32 kb/s 24 kb/s 16 kb/s b3 b4 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 notes: b 2 b 3 b 4 12 12 12 b 1 12 b 2 b 3 b 4 12 12 12 b1 b2 b3 b4 1234 1234 123x 123x b3 b4 b 1 12 b 2 b 3 b 4 12 12 12 x = undetermined logic level output; don? care input two frame delay from data input to data output outputs high impedance outside of channel strobe boundaries
MT9126 8-10 figure 6 - ssi pcm and adpcm bypass relative timing adpcmo/i bclk enb1 enb2/ f0od pcmi/o1 765 3 4 210 b1 b2 765 3 4 210 pcmi/o2 765 3 4 210 b3 b4 765 3 4 210 765 3 4210 765 3 4210 sel = 0 adpcmo/i pcmi/o1 123 x 4xxx sel = 1 b1 b2 pcmi/o2 b3 b4 sel = 0 123 x 4 xxx 123 x 4 xxx 12341234 1234 1234 adpcm o/i pcmi/o1 pcmi/o2 12x x xxxx b1 b2 b3 b4 12x x x xxx 12x x x xxx 12x x x xxx 12121212 1212 1212 b1 b2 b3 b4 b1 b2 b3 b4 32 kb/s using bits 1 2 3 4 24 kb/s where bit 4 = x 16 kb/s ssi pcm bypass ssi adpcm bypass sel = 1 123 x 4xxx x = undetermined logic level output; don? care input two frame delay from data input to data output outputs high impedance outside of channel strobe boundaries
MT9126 8-11 figure 7 - st-bus 8-bit companded pcm relative timing mclk/ c4i f0i adpcmi adpcmo c2o (output) b1 b2 b3 b4 en1 (output) en2 (output) pcmi2 pcmo2 b3 b4 pcmi1 pcmo1 b1 b2 dc d c b1 sel=0 sel=1 b2 b4 b3 b1 b2 b4 b3 b1 b2 b4 b3 b1 b2 b4 b3 32 kb/s is shown in 24 kb/s, bit 4 becomes ? 16 kb/s sel operates for enb2/ f0od 7654 7654 3 21 0 3 21 0 7654 7654 3 21 0 3 21 0 7654 7654 3 21 0 3 21 0 01 7654 3 21 0 121 2 1 21 2 121 2 1 21 2 121 2 1 21 2 121 2 1 21 2 123 4 123 4 1 23 4 1 23 4 7654 7654 3 21 0 3 21 0 01 7654 3 21 0 transparent relay of d- and c- channels when enb1=0 01 7654 3 21 0 123 4 123 4 1 23 4 1 23 4 01 7654 3 21 0 outputs=high impedance inputs = don? care x = undetermined logic level output; don? care input two frame delay from data input to data output outputs high impedance outside of channel boundaries 16 kb/s only
MT9126 8-12 figure 8 - st-bus 16-bit linear pcm relative timing mclk/ c4i f0i c2o adpcmi/o note: d &c channels not supported in this mode. sel operated for pcmi/o1 pcmi/o2 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 sss 12 11 10 9 8 7 6 5 4 3 2 1 0 b1 b2 b3 b4 adpcmi/o (32/24 kb/s) (16 kb/s) f0od/enb2 en1 (output) bit 4 = x at 24 kbit/s b 1 12 sel = 1 sel = 0 b 2 b 3 b 4 12 12 12 b 1 12 b 2 b 3 b 4 12 12 12 1234 1234 1234 1234 b1 b2 b3 b4 16kb/s only outputs = high impedance inputs = don? care x = undetermined logic level output; don? care input two frame delay from data input to data output outputs high impedance outside of channel boundaries
MT9126 8-13 figure 9 - st-bus pcm and adpcm bypass relative timing en1 (output) en2 (output) mclk/ c4i f0i c2o adpcmi adpcmo sel=0 sel=1 pcmi1 pcmo1 b1 b2 dc pcmi2 pcmo2 b3 b4 b1/b3 b2/b4 dc adpcmi/o adpcmi/o b3 b4 pcmi/o1 pcmi/o2 d c b1 b2 dc b3 b4 b1 b2 32 kb/s 24 kb/s bit 4 = x (16 kb/s) pcmi/o1 pcmi/o2 d c b1 sel=0 sel=1 b2 b4 b3 b3 b4 c d x xx x b2 b1 01 01 01 p c m b y p a s s a d p c m b y p a s s xxxx 0 1 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 x x x x x x b1 b2 b4 b3 1 2 x x x x x x 1 2 x x x x x x 1 2 x x x x x x 1 2 3 4 xxxx 1 2 3 4 xxxx 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 1 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 1 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 1 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 1 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 outputs = high impedance inputs = don? care x = undetermined logic level output; don? care input two frame delay from data input to data output outputs high impedance outside of channel boundaries enb2/ f0od
MT9126 8-14 figure 10 - data throughput pcmi1/2 adpcmo enb1 or enb2 f0i ms1 or 4 where ms2, 3, 5, 6 = 0 frame n-1 frame n frame n+1 pcm byte " x " latched into device during frame n-1 pcm byte " x " processed according to msn input states latched during frame n adpcm word " x " output from device during frame n+1 32 kb/s 24 kb/s 32 kb/s this diagram shows the conversion sequence from pcm to adpcm. the same pipelining occurs in the reverse adpcm to pcm direction. total delay from data input to data output = 2 frames. byte "x" word "x" processing delay through the device in order to accommodate variable rate pcm and adpcm interfaces, the serial input and output streams require a complete frame to load internal shift registers. internal frame alignment of the encoding/decoding functions are taken from either of the f0i or enb1 & enb2 input strobes depending upon the device operating mode (i.e., st-bus or ssi). the encoding/decoding of all channels then takes one frame to complete before the output buffers are loaded. this results in a two frame transcoding delay. the two frame delay also applies to the d and c channels and to the pcm and adpcm bypass functions. (see figure 10.) note: when changing the relative positions of the enb1 and enb2 strobes, precaution must be taken to ensure that two conditions are met. they are: 1) there must be at least 512 master clock cycles between consecutive rising edges of enb1. this condition also holds true for enb2. 2) the enb1 strobe must alternate with the enb2 strobe. violation of these requirements may cause noise on the output channels. applications figure 11 depicts an isdn line card utilizing the mt8910 ? interface transciever and MT9126 adpcm transcoder. this central office application implements the network end of a pair-gain system. figure 12 depicts an adpcm to linear pcm converter for applications where further, value added, functions are being performed via digital signal processor. access to linear coded pcm reduces the overhead of the dsp by removing the need for a companded to linear conversion. the linear pcm capability of the adpcm transcoder in conjunction with the frame alignment signal en1 allows direct connection to the serial port of both motorola and texas instruments digital signal processors. daisy-chaining via the delayed frame strobe output ensures that the adpcm array is distributed over the complete 2048 kbit bandwidth. if the dsp has a second serial port then access to the processed pcm can be had directly. for processors with only one serial port the mt8920 connected to the dsp parallel port will provide serial access by parallel to serial conversion. the same daisy- chained arrangement of quad adpcm transcoders will provide a general system resource for pcm- adpcm conversion by setting the device to non- linear operation.
MT9126 8-15 figure 11 - isdn line card with 32 kbit/s adpcm lin - f0b c4b f0od dsto dsti mt8910 lin+ lout + lout - mt8980 dx st1o st1i c4i f0i f0i f0od c4i 1 2 8 pcmi1 pcmo2 f0i f0od c4i adpcmi adpcmo pcmi1 pcmo1 mclk/c4i f0i MT9126 pcmi2 pcmo2 st2o st2i pcmi2 pcmo1 pcmi1 pcmo2 f0i f0od c4i pcmi2 pcmo1 pcmi1 pcmo2 f0i f0od c4i pcmi2 pcmo1 t r 2 tr 1 t r 8 c4i f0i
MT9126 8-16 figure 12 - st-bus to dsp platform clkr clkx fsr fsx irq0 dr dx system frame pulse system 4.096mhz s t p a 2nd serial port if available stpa port adpcm bus ti dsp c2o f0i mclk/ c4i pcmo1 pcmo2 adpcmo adpcmi pcmi1 pcmi2 linear en1 enb2/ f0od c2o f0i mclk/ c4i pcmo1 pcmo2 adpcmo adpcmi pcmi1 pcmi2 linear en1 enb2/ f0od c2o f0i mclk/ c4i pcmo1 pcmo2 adpcmo adpcmi pcmi1 pcmi2 linear en1 enb2/ f0od c2o f0i mclk/ c4i pcmo1 pcmo2 adpcmo adpcmi pcmi1 pcmi2 linear en1 enb2/ f0od MT9126 MT9126 MT9126 MT9126 +5v +5v +5v +5v st-bus mt8920
MT9126 8-17 * exceeding these values may cause permanent damage. functional operation under these conditions is not implied. typical ?ures are at 25 c and are for design aid only: not guaranteed and not subject to production testing. typical ?ures are at 25 c and are for design aid only: not guaranteed and not subject to production testing. * dc electrical characteristics are over recommended temperature and supply voltage. absolute maximum ratings* parameter symbol min max units 1 supply voltage v dd -v ss -0.3 7.0 v 2 voltage on any i/o pin v i | v o v ss -0.3 v dd + 0.3 v 3 continuous current on any i/o pin i i | i o 20 ma 4 storage temperature t st -65 150 c 5 package power dissipation p d 500 mw recommended operating conditions - voltages are with respect to ground (v ss ) unless otherwise stated. characteristics sym min typ max units test conditions 1 supply voltage v dd 4.5 5.0 5.5 v 2 ttl input high voltage 2.4 v dd v 400mv noise margin 3 ttl input low voltage v ss 0.4 v 400mv noise margin 4 cmos input high voltage 4.5 v dd v 5 cmos input low voltage v ss 0.5 v 6 operating temperature t a -40 +85 c dc electrical characteristics - voltages are with respect to ground (v ss ) unless otherwise stated. characteristics sym min typ max units test conditions 1 supply current i cc i dd 5 100 7.5 a ma pwrdn = 0 pwrdn = 1, clocks active 2 input high voltage (ttl) v ih 2.0 v 3 input low voltage (ttl) v il 0.8 v 4 m c l k / c 4 i input high voltage (cmos) v ihc 3.5 v 5 input low voltage (cmos) v ilc 1.5 v 6 input leakage current i ih /i il 0.1 10 av in =v ss to v dd 7 high level output voltage v oh 2.4 v i ol =5.0ma 8 low level output voltage v ol 0.4 v i ol =5.0ma 9 high impedance leakage i oz 110 av in =v ss to v dd 10 output capacitance c o 10 pf 11 input capacitance c i 8pf 12 p w r d n positive threshold voltage hysteresis negative threshold voltage v+ v h v- 3.7 1.0 1.3 v v v
MT9126 8-18 ? timing is over recommended temperature & power supply voltages. typical ?ures are at 25 c and are for design aid only: not guaranteed and not subject to production testing. ac electrical characteristics ? - serial pcm/adpcm interfaces (see figure 13) voltages are with respect to ground (v ss ) unless otherwise stated. characteristics sym min typ ? max units test conditions 1 bclk clock high t bch 80 ns t bcp =200 ns 2 bclk clock low t bcl 80 ns t bcp =200 ns 3 bclk period t bcp 200 7900 ns 4 data output delay (excluding ?st bit) t dd 80 ns c l =150pf//r l =1k 5 output active to high z t ahz 80 ns c l =150pf//r l =1k 6 strobe signal setup t sss 80 t bcp - 80 ns 7 strobe signal hold t ssh 80 t bcp - 80 ns 8 data input setup t dis 50 ns 9 data input hold t dih 50 ns 10 strobe to data delay (?st bit) t sd 80 ns c l =150pf//r l =1k 11 f0i setup t f0is 50 122 150 ns 12 f0i hold t f0ih 50 122 150 ns 13 mclk/ c4i duty cycle t h /t l x100 40 50 60 % 14 f0od delay t dfd 60 ns c l =150pf//r l =1k 15 f0od pulse width t dfw 244 ns c l =150pf//r l =1k 16 mclk/ c4i period t c4p 61 244.2 ns 17 data output delay t dsd 95 ns c l =150pf//r l =1k 18 data in hold time t dsh 50 ns 19 data in setup time t dss 50 ns
MT9126 8-19 figure 13 - serial port timing figure 14 - st-bus timing for external signal generation ac electrical characteristics ? - st-bus c2o conversion voltages are with respect to ground (v ss ) unless otherwise stated. characteristics sym min typ ? max units test conditions 1 delay mclk/ c4i falling to c2o rising t d1 100 ns 150pf//1k load 2 delay mclk/ c4i falling to enable t d2 100 ns 150pf//1k load bclk enb1 or enb2 pcmi/adpcmi pcmo/adpcmo mclk/ c4i f0i s s i s t - b u s t bcp t bch t bcl t sss t ssh t dis t dih t dss t dsh t dd t ahz t dsd t h t f0ih t l t c4p t dfd v ih v il v ih v il v ih v il v oh v ol v ihc v ilc v ih v il t sd v oh v ol t f0is t dfd t dfw f0od f0i mclk/ c4i c2o en1 en2 t d1 t d2 t d2 v ih v il v ihc v ilc v oh v ol v oh v ol
MT9126 8-20 ? timing is over recommended temperature & power supply voltages. typical ?ures are at 25 c and are for design aid only: not guaranteed and not subject to production testing. figure 15 - ssi mode select set-up and hold timing figure 16 - st-bus mode select set-up and hold timing ac electrical characteristics ? - mode select timing (see figures 15 & 16) voltages are with respect to ground (v ss ) unless otherwise stated. characteristics sym min typ ? max units test conditions 1 mode select setup t su 500 ns mclk/ c4i=4096 khz 2 mode select hold t hold 500 ns t su t hold enb1 (input) ms1 to ms6 v ih v il v ih t su t hold ms1 to ms6 mclk/ c4i f0i refer to figure 14 for st-bus f0i timing. v ih v il
MT9126 8-21 lead soic package - s suffix notes: 1. controlling dimensions in parenthesis ( ) are in millimeters. 2. converted inch dimensions are not necessarily exact. dim 16-pin 18-pin 20-pin 24-pin 28-pin min max min max min max min max min max a 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) a 1 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) b 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.030 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) c 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) d 0.398 (10.1) 0.413 (10.5) 0.447 (11.35) 0.4625 (11.75) 0.496 (12.60) 0.512 (13.00) 0.5985 (15.2) 0.614 (15.6) 0.697 (17.7) 0.7125 (18.1) e 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) e 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) h 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) l 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) pin 1 a 1 b e e a l h c notes: 1) not to scale 2) dimensions in inches 3) (dimensions in millimeters) 4) a & b maximum dimensions include allowable mold flash d l 4 mils (lead coplanarity)
package outlines plastic j-lead chip carrier - p-suf?x f d 1 d h e 1 i a 1 a g d 2 e e 2 dim 20-pin 28-pin 44-pin 68-pin 84-pin min max min max min max min max min max a 0.165 (4.20) 0.180 (4.57) 0.165 (4.20) 0.180 (4.57) 0.165 (4.20) 0.180 (4.57) 0.165 (4.20) 0.200 (5.08) 0.165 (4.20) 0.200 (5.08) a 1 0.090 (2.29) 0.120 (3.04) 0.090 (2.29) 0.120 (3.04) 0.090 (2.29) 0.120 (3.04) 0.090 (2.29) 0.130 (3.30) 0.090 (2.29) 0.130 (3.30) d/e 0.385 (9.78) 0.395 (10.03) 0.485 (12.32) 0.495 (12.57) 0.685 (17.40) 0.695 (17.65) 0.985 (25.02) 0.995 (25.27) 1.185 (30.10) 1.195 (30.35) d 1 /e 1 0.350 (8.890) 0.356 (9.042) 0.450 (11.430) 0.456 (11.582) 0.650 (16.510) 0.656 (16.662) 0.950 (24.130) 0.958 (24.333) 1.150 (29.210) 1.158 (29.413) d 2 /e 2 0.290 (7.37) 0.330 (8.38) 0.390 (9.91) 0.430 (10.92) 0.590 (14.99) 0.630 (16.00) 0.890 (22.61) 0.930 (23.62) 1.090 (27.69) 1.130 (28.70) e 0 0.004 0 0.004 0 0.004 0 0.004 0 0.004 f 0.026 (0.661) 0.032 (0.812) 0.026 (0.661) 0.032 (0.812) 0.026 (0.661) 0.032 (0.812) 0.026 (0.661) 0.032 (0.812) 0.026 (0.661) 0.032 (0.812) g 0.013 (0.331) 0.021 (0.533) 0.013 (0.331) 0.021 (0.533) 0.013 (0.331) 0.021 (0.533) 0.013 (0.331) 0.021 (0.533) 0.013 (0.331) 0.021 (0.533) h 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) 0.050 bsc (1.27 bsc) i 0.020 (0.51) 0.020 (0.51) 0.020 (0.51) 0.020 (0.51) 0.020 (0.51) notes: 1) not to scale 2) dimensions in inches 3) (dimensions in millimeters) 4) for d & e add for allowable mold protrusion 0.010" e: (lead coplanarity) general-10
package outlines plastic dual-in-line packages (pdip) - e suf?x note: controlling dimensions in parenthesis ( ) are in millimeters. dim 8-pin 16-pin 18-pin 20-pin plastic plastic plastic plastic min max min max min max min max a 0.210 (5.33) 0.210 (5.33) 0.210 (5.33) 0.210 (5.33) a 2 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b 2 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) c 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356) d 0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9) d 1 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) e 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) e 1 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) e 0.100 bsc (2.54) 0.100 bsc (2.54) 0.100 bsc (2.54) 0.100 bsc (2.54) e a 0.300 bsc (7.62) 0.300 bsc (7.62) 0.300 bsc (7.62) 0.300 bsc (7.62) l 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) e b 0.430 (10.92) 0.430 (10.92) 0.430 (10.92) 0.430 (10.92) e c 0 0.060 (1.52) 0 0.060 (1.52) 0 0.060 (1.52) 0 0.060 (1.52) e 1 32 1 e n-2 n-1 n l d d 1 b 2 a 2 e b c e a notes: 1) not to scale 2) dimensions in inches 3) (dimensions in millimeters) a e b e c general-8
package outlines plastic dual-in-line packages (pdip) - e suf?x dim 22-pin 24-pin 28-pin 40-pin plastic plastic plastic plastic min max min max min max min max a 0.210 (5.33) 0.250 (6.35) 0.250 (6.35) 0.250 (6.35) a 2 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b 2 0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) c 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) d 1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2) d 1 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) e 0.390 (9.91) 0.430 (10.92) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) e 0.290 (7.37) .330 (8.38) e 1 0.330 (8.39) 0.380 (9.65) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) e 1 0.246 (6.25) 0.254 (6.45) e 0.100 bsc (2.54) 0.100 bsc (2.54) 0.100 bsc (2.54) 0.100 bsc (2.54) e a 0.400 bsc (10.16) 0.600 bsc (15.24) 0.600 bsc (15.24) 0.600 bsc (15.24) e a 0.300 bsc (7.62) e b 0.430 (10.92) l 0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08) a 15 15 15 15 e 1 32 1 e n-2 n-1 n l d d 1 b 2 a 2 e b c e a notes: 1) not to scale 2) dimensions in inches 3) (dimensions in millimeters) a e b a shaded areas for 300 mil body width 24 pdip only
m mitel (design) and st-bus are registered trademarks of mitel corporation mitel semiconductor is an iso 9001 registered company copyright 1999 mitel corporation all rights reserved printed in canada technical documen t a tion - n o t for resale world headquarters - canada tel: +1 (613) 592 2122 fax: +1 (613) 592 6909 north america asia/paci?c europe, middle east, tel: +1 (770) 486 0194 tel: +65 333 6193 and africa (emea) fax: +1 (770) 631 8213 fax: +65 333 6192 tel: +44 (0) 1793 518528 fax: +44 (0) 1793 518581 http://www.mitelsemi.com information relating to products and services furnished herein by mitel corporation or its subsidiaries (collectively mitel) is believed to be reliable. however, mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by mitel or licensed from third parties by mitel, whatsoever. purchasers of products are also hereby noti?ed that the use of product in certain ways or in combination with mitel, or non-mitel furnished goods or services may infringe patents or other intellectual property rights owned by mitel. this publication is issued to provide information only and (unless agreed by mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. the products, their speci?cations, services and other information appearing in this publication are subject to change by mitel without notice. no warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a speci?c piece of equipment. it is the users responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. manufacturing does not necessarily include testing of all functions or parameters. these products are not suitable for use in any medical products whose failure to perform may result in signi?cant injury or death to the user. all products and materials are sold and services provided subject to mitels conditions of sale which are available on request.

▲Up To Search▲

Price & Availability of MT9126

	To Download MT9126 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .